This post is part of a creative challenge for May (extended into June) to create a skirt from punctured bicycle inner tubes. You can find all posts in this series here, and all my challenges here.
I’m SO excited to share this with you. Now that it’s done I can look back on the process fondly and pretend like it wasn’t a whole lot of work, especially towards the end. The hem was so time consuming!
Connecting the Strips
I ended my last blog post having cut all the strips to make up the front and back panels for the skirt. The next step was assembling those panels.
I had some strips leftover from my obsessive period of coiled basket making, which made perfect backings behind the joins so I could zig zag across to connect. Below are the finished – well, sewn together panels. All those straggly threads needed to be tied off by hand, which took a couple of hours in front of the telly.
There were some tricky bits, and I have a few lessons:
- Remember where you’re putting your zip! I forgot and assembled the back as one piece. Fixing it involved unpicking, which was frustrating but didn’t detract from the final piece as the holes left from the stitching got cut off to expose the zipper teeth.
- Sewing the front to the back was the most frustrating part as the edges were so curved. It would’ve been easier to save the straightest stitching on the front of the skirt for last. The double sided tape I use doesn’t cooperate sometimes, so for those very curved sections I held the top together with masking tape too, pulling it back as I went.
My machine was not consistent with zig zags for some reason. Sometimes it would be fine, but other times I’d get loads of skipped stitches and have to go back over it again. I’m not sure if it was an issue with thickness, tension, needle, or something else. I tried adjusting everything I could could think of, and nothing fixed it consistently.
It doesn’t replicate on fabric, so inner tube may just be a bit too much for my machine to handle. I want to buy an industrial machine eventually, but I was hoping I could get by with my New Home for a bit longer so I could save more money.
I’ve got two last ideas:
- Getting my machine serviced – I haven’t used it much, but it must take a lot to sew through inner tube
- Try a different brand of needle, as I used to not have this issue and that’s the only thing I can think of that I’d switched.
Finishing the Hem
After main skirt was in one piece, I tackled the hem. I really ummed and ahhed about what I’d do- whether to fold it over or just cut it to length (it’s not like it’s going to fray) or back it as I did with the joins in another strip of inner tube.
My main worry was about long term stability. The hem is a point of strain and if I used an inner tube strip my fear was it would be TOO stretchy and more likely to snap the thread while walking or climbing stairs when those seams were under more pressure. Just folding over wouldn’t protect those seams at all, and may stick out weirdly due to the wavy nature of inner tubes.
So I just trimmed everything to the final length and used some black twill tape inside.
The tape does have a little give, but it’s not stretchy so it should protect the bottoms of those seams.
It wasn’t as simple as just stitching that on over the top though. For each join I:
- Marked just beyond the width of the twill tape
- Unpicked my stitching to that point
- Clipped the backing strip of inner tube
- Redid the stitched by hand using the original holes
Why did I do this? Sudden changes in fabric width can cause tension issues and skipped stitches. Given the issues I’d already had, I didn’t want a wonky hem.
Thankfully all my work paid off and I didn’t have a single skipped stitch!
Last but not least was the waistband.
Cutting & Attaching the Waistband
I saved the waistband until last because I wasn’t sure how I would handle it.
The only quibble I had with my second fabric version of the skirt was the straight waistband. It stood away from a my body a little bit in places – probably not noticeable to anyone but me, but I knew it could be better. A curved waistband, like I had on my upcycled initial test of the pattern, would lie flush but I didn’t have a pattern piece for it.
But inner tube often curves when you cut into it, as the middle in longer than the sides. So I thought as a lazy test I’d just cut it and see what happened:
As it happened, the curve fit my body really well!
Attaching it was another tricky curved seam, but the double sided tape below and making tape above sandwich worked a treat again. I backed this seam with twill tape as well to prevent my joins from splitting.
The last few touches were the popper and label.
The Finished Skirt
Drumroll please: here’s the finished inner tube skirt! Hopefully it’s obvious enough it’s made from bicycle inner tubes, and not just very badly sewn fabric.
The gallery below shows the outside and the inside, front and back:
One of my favourite things when sewing is to make something as neat as possible, inside and out, and I’m really happy with both here. I made sure to put some writing on the strips I used inside – it’s the equivalent of using crazy fabric for your pocket bags: no one else knows it’s there but it brings me joy.
Here’s a little twirl so you can see the skirt in action!
Final Thoughts & Takeaways
This was a ridiculous thing to make with the weather as hot as it’s been. While I’m so proud of the final result, and kind of desperate to wear it out, it’ll have to wait until the temperature cools. Maybe by the time I’m fully vaccinated and feel comfortable doing markets again, the weather will be more cooperative.
The skipped stitches on my machine are frustrating, and part of the reason I’ve put a pause on making larger things out of inner tubes for now. Here’s hoping I can get this machine working again – at least for a new product I’ve got in mind.
I’m giving myself a break from these inner tube challenges for the rest of June, and probably July. While they’re a lot of fun, they do take up a bit of time, and there’s a lot of work I’d like to do on my business and my current (and future) product lines.
2 thoughts on “Inner Tube Skirt – Update 5: Done!”
What about sealing all seams with EVOSTICK and letting it cure for 48 hours.
I haven’t used that adhesive before. I’ll take a look, thanks for the suggestion!